|
This is a list of published〔This list generally excludes draft versions.〕 International Organization for Standardization (ISO) standards and other deliverables.〔(ISO deliverables ) include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".〕 For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.〔(【引用サイトリンク】title=Standards catalog )〕 The standards are protected by copyright and most of them must be purchased. However about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC1) have been made freely and publicly available.〔(【引用サイトリンク】title=Freely Available Standards )〕 ==ISO 1 – ISO 99== * ISO 1:2002 Geometrical Product Specifications (GPS) – Standard reference temperature for geometrical product specification and verification * ISO 2:1973 Textiles – Designation of the direction of twist in yarns and related products * ISO 3:1973 Preferred numbers – Series of preferred numbers * ISO 4:1997 Information and documentation – Rules for the abbreviation of title words and titles of publications * ISO 5 Photography and graphic technology – Density measurements * ISO 6:1993 Photography – Black-and-white pictorial still camera negative film/process systems – Determination of ISO speed * ISO 7 Pipe threads where pressure-tight joints are made on the threads * ISO 8:1977 Documentation – Presentation of periodicals * ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages * ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins * ISO 12:1987 Aerospace – Pipelines – Identification * ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification * ISO 15:2011 Radial bearings—Boundary dimensions, general plan * ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch) * ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers * ISO 18:1981 Documentation – Contents list of periodicals * ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains * ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances * ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications * ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications * ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications * ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications * ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications (without replacement ) * ISO 31 Quantities and units (replaced with ISO/IEC 80000 ) * ISO 32:1977 Gas cylinders for medical use—Marking for identification of content * ISO 34 * *ISO 34-1:2010 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 1: Trouser, angle and crescent test pieces * *ISO 34-2:2011 Rubber, vulcanized or thermoplastic—Determination of tear strength—Part 2: Small (Delft) test pieces * ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability * ISO 36:2011 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics * ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties * ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps (without replacement ) * ISO 43:1976 Aircraft—Jacking pads * ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation * ISO 45:1990 Aircraft—Pressure refuelling connections * ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets * ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD) * ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1 * ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 (without replacement ) * ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile * ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules * ISO 55:1977 Seedlac—Specification (without replacement ) * ISO 57:1975 Bleached lac—Specification (without replacement ) * ISO 60:1977 Plastics—Determination of apparent density of material that can be poured from a specified funnel * ISO 61:1976 Plastics—Determination of apparent density of moulding material that cannot be poured from a specified funnel * ISO 62:2008 Plastics—Determination of water absorption * ISO 63:1975 Flat transmission belts—Lengths (Replaced with ISO 22 ) * ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1 * ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size (without replacement ) * ISO 68 ISO general-purpose screw threads – Basic profile * * ISO 68-1:1998 Metric screw threads * * ISO 68-2:1998 Inch screw threads * ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions * ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions * ISO 71:1977 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions * ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions * ISO 75 Plastics—Determination of temperature of deflection under load * * ISO 75-1:2013 Plastics—Determination of temperature of deflection under load—Part 1: General test method * * ISO 75-2:2013 Plastics—Determination of temperature of deflection under load—Part 2: Plastics and ebonite * * ISO 75-3:2004 Plastics—Determination of temperature of deflection under load—Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics * ISO 76:2006 Rolling bearings—Static load ratings * ISO 78 Chemistry — Layouts for standards * * ISO 78-2:1999 Chemistry—Layouts for standards—Part 2: Methods of chemical analysis * * ISO 78-3:1983 Chemistry—Layouts for standards—Part 3: Standard for molecular absorption spectrometry * * ISO 78-4:1983 Layouts for standards—Part 4: Standard for atomic absorption spectrometric analysis * ISO 82:1974 Steel—Tensile testing (replaced with ISO 6892-1 ) * ISO 83:1976 Steel—Charpy impact test (U-notch) (replaced with ISO 148-1 ) * ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0,5 mm thick (replaced with ISO 6892-1 ) * ISO 89:1974 Steel—Tensile testing of wire (replaced with ISO 6892-1 ) * ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities * * ISO 90-1:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 1: Open-top cans * * ISO 90-2:1997 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 2: General use containers * * ISO 90-3:2000 Light gauge metal containers—Definitions and determination of dimensions and capacities—Part 3: Aerosol cans * ISO 91 Petroleum measurement tables * * ISO 91-1:1992 Petroleum measurement tables—Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F * * ISO 91-2:1991 Petroleum measurement tables—Part 2: Tables based on a reference temperature of 20 degrees C * ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right) * ISO 93 Textile machinery and accessories—Cylindrical sliver cans * * ISO 93-1:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 1: Main dimensions * * ISO 93-2:2006 Textile machinery and accessories—Cylindrical sliver cans—Part 2: Spring bottoms * ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames * ISO 96 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames * * ISO 96-1:2009 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames—Part 1: Flange rings T and SF and their travellers * * ISO 96-2:2009 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames—Part 2: HZ- and J-rings and their travellers * ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travellers * ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「List of International Organization for Standardization standards」の詳細全文を読む スポンサード リンク
|